2004 Hummer H2
Vehicle Specs & Maintenance Data
The 2004 Hummer H2 maintenance specs on this page cover the key fluids, torque values, and wear items you need for routine service. Use these numbers as a quick reference when performing oil changes, tire rotations, brake jobs, and other scheduled maintenance on your Hummer H2.
For oil changes, the 2004 Hummer H2 takes 5W-30 Full Synthetic motor oil with a capacity of 6 quarts. Brake fluid type is DOT 3, the recommended coolant is Dex-Cool (OAT), and transmission fluid is Dexron VI. Always use the manufacturer-recommended fluids to maintain warranty coverage and engine longevity.
When mounting wheels on the Hummer H2, torque the lug nuts to 140 ft-lbs using a calibrated torque wrench. Over- or under-torquing can lead to warped brake rotors or loose wheels. Re-torque after 50 to 100 miles on newly installed wheels.
There are 4 NHTSA safety recalls on file for the 2004 Hummer H2. Check the Recalls tab below for full details.
Specifications on this page are compiled from multiple publicly available sources including manufacturer documentation, NHTSA data, and automotive databases. Always cross-reference with your owner's manual or official factory documentation before purchasing parts or performing any service.
The 2004 Hummer H2 uses 5W-30 Full Synthetic motor oil (6 qt capacity), requires lug nuts torqued to 140 ft-lbs, takes DOT 3 brake fluid.
Enter a diagnostic trouble code to see causes, symptoms, and fixes for the 2004 Hummer H2.
No known problems reported for this vehicle yet.
4 NHTSA safety recalls for the 2004 Hummer H2. Check your VIN at NHTSA.gov
STEERING
CERTAIN FABTECH AFTERMARKET REPLACEMENT PITMAN ARMS, P/NOS. FTS71000 AND FTS71001, INSTALLED FOR USE ON CERTAIN 2001-2006 GM C/K 2500 PICK UP TRUCKS AND SPORT UTILITY VEHICLES. THE PIN LOCATED INSIDE THE PITMAN ARM CAN SHEAR OFF DUE TO A REVERSE BENDING FATIGUE CONDITION, RESULTING IN A TOTAL LOSS OF STEERING CONTROL.
LOSS OF STEERING CONTROL COULD LEAD TO A VEHICLE CRASH WITH POTENTIAL INJURY OR DEATH.
FABTECH WILL NOTIFY OWNERS AND REPLACE THE PITMAN AND IDLER ARMS FREE OF CHARGE. THE RECALL IS EXPECTED TO BEGIN DURING FEBRUARY 2006. OWNERS MAY CONTACT FABTECH AT 909-597-7800.
SEAT BELTS:REAR/OTHER
ON CERTAIN CREW CAB PICKUP TRUCKS AND SPORT UTILITY VEHICLES, THE 2ND ROW CENTER OCCUPANT SEAT BELT ROUTING MAY MAKE IT DIFFICULT TO POSITION THE LAP PORTION OF THE SAFETY BELT LOW AROUND THE HIPS OF OCCUPANTS, ESPECIALLY SMALLER OCCUPANTS, SEATED IN THIS POSITION. APPROPRIATE USE OF A CHILD SEAT OR BOOSTER SEAT, AS RECOMMENDED FOR SMALL CHILDREN, DOES IMPROVE THE FIT CONDITION FOR THIS USER GROUP. IN ADDITION TO INSTRUCTIONS ON PROPER INFANT AND YOUNG CHILD RESTRAINT (WITH CHILD SEATS OR BOOSTERS), SPECIAL VERBIAGE FOR RESTRAINING OLDER CHILD IS INCLUDED IN THE OWNER'S MANUAL. ALSO, THE SUGGESTED SEAT BELT FIT/ROUTING FOR ADULTS, IRRESPECTIVE OF SEATING POSITION, IS DESCRIBED IN THE OWNER'S MANUAL TEXT.
A LAP PORTION OF THE SEAT BELT ROUTING THAT IS NOT LOW AND SNUG ON THE HIPS CAN ALLOW THE LAP BELT TO RIDE UP ON AN OCCUPANT'S ABDOMEN INSTEAD OF FITTING LOW AROUND THEIR HIPBONES, AND THEREFORE, CAN EXPOSE THEM TO MORE RISK OF ABDOMINAL AND INTERNAL ORGAN INJURY.
DEALERS WILL CUT OPEN THE GUIDE LOOP, REMOVE A PORTION OF THE LOOP, AND THEN THE REMAINING TWO SIDES SHOULD BE FOLDED OVER AND SECURED WITH A RETAINER FREE OF CHARGE. THE RECALL BEGAN ON JULY 21, 2005. OWNERS MAY CONTACT CADILLAC AT 1-866-982-2339, CHEVROLET AT 1-800-630-2438, GMC AT 1-866-996-9463, OR HUMMER AT 1-800-732-5493.
SERVICE BRAKES, HYDRAULIC
CERTAIN TRUCKS, SPORT UTILITY VEHICLES, AND VANS EQUIPPED WITH BOSCH HYDRO-BOOST BRAKE ASSEMBLIES, THE HYDRAULIC BRAKE BOOSTER PRESSURE ACCUMULATOR MAY CRACK AND SEPARATE FROM THE HYDRO-BOOST ASSEMBLY DURING NORMAL OPERATING CONDITIONS.
IF A SEPARATION OCCURRED AND THE HOOD OF THE VEHICLE WERE OPEN, FRAGMENTS FROM THE ACCUMULATOR COULD CAUSE INJURY TO PEOPLE IN THE IMMEDIATE AREA. THE PRESENCE OF THIS CRACK OR FRACTURED SURFACE COULD ALLOW THE HYDRAULIC FLUID TO LEAK FROM THE ACCUMULATOR CIRCUIT OF THE BOOSTER ASSEMBLY. THE LOSS OF FLUID WOULD CAUSE INCREASED STEERING AND BRAKING EFFORT AND A CRASH MAY OCCUR WITHOUT PRIOR WARNING.
DEALERS WILL TEST THE HYDRO-BOOST ASSEMBLY FOR FUNCTIONAL OPERATION OF THE TWO-FUNCTION VALVE. IF THE HYDRO-BOOST ASSEMBLY FAILS THE TEST, DEALERS WILL REPLACE THE ASSEMBLY FREE OF CHARGE. THE RECALL BEGAN ON MARCH 23, 2005. OWNERS MAY CONTACT CHEVROLET AT 1-800-630-2438, GMC TRUCKS AT 1-866-996-9463 AND HUMMER AT 1-800-732-5493.
SERVICE BRAKES, HYDRAULIC
CERTAIN SPORT UTILITY VEHICLES, PICKUP TRUCKS, AND PASSENGER VANS FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 135, ?PASSENGER CAR BRAKE SYSTEMS.? SOME OF THESE VEHICLES WERE PRODUCED WITH AN OUT-OF-SPECIFICATION BRAKE HYDRO-BOOST HOUSING RELIEF VALVE BORE.
CONSEQUENTLY, THE VALVE O-RING SEAL MAY FRACTURE. STEERING EFFORTS MAY BE SLIGHTLY INCREASED WHILE BRAKING OR PARKING. UNDER CERTAIN DRIVING CONDITIONS, A FRACTURED SEAL MAY REQUIRE A SLIGHT INCREASE IN THE APPLIED BRAKE PEDAL EFFORT TO ACHIEVE THE SAME VEHICLE DECELERATION RATE AS PRIOR TO THE SEAT FRACTURE.
DEALERS ARE TO REPLACE THE HYDRO-BOOST RELIEF VALVE. THE RECALL BEGAN ON JUNE 18, 2004. OWNERS SHOULD CONTACT CADILLAC AT 1-866-982-2339; CHEVROLET AT 1-800-630-2438; GMC AT 1-866-996-9463; OR HUMMER AT 1-866-486-6376.