1996 Ford F-250
Vehicle Specs & Maintenance Data
The 1996 Ford F-250 maintenance specs on this page cover the key fluids, torque values, and wear items you need for routine service. Use these numbers as a quick reference when performing oil changes, tire rotations, brake jobs, and other scheduled maintenance on your Ford F-250.
For oil changes, the 1996 Ford F-250 takes 5W-30 motor oil with a capacity of 6 quarts. Brake fluid type is DOT 3, the recommended coolant is Motorcraft Gold (OAT), and transmission fluid is Mercon LV. Always use the manufacturer-recommended fluids to maintain warranty coverage and engine longevity.
When mounting wheels on the Ford F-250, torque the lug nuts to 140 ft-lbs using a calibrated torque wrench. Over- or under-torquing can lead to warped brake rotors or loose wheels. Re-torque after 50 to 100 miles on newly installed wheels.
There are 5 NHTSA safety recalls on file for the 1996 Ford F-250. Check the Recalls tab below for full details.
Specifications on this page are compiled from multiple publicly available sources including manufacturer documentation, NHTSA data, and automotive databases. Always cross-reference with your owner's manual or official factory documentation before purchasing parts or performing any service.
The 1996 Ford F-250 uses 5W-30 motor oil (6 qt capacity), requires lug nuts torqued to 140 ft-lbs, takes DOT 3 brake fluid.
Enter a diagnostic trouble code to see causes, symptoms, and fixes for the 1996 Ford F-250.
No known problems reported for this vehicle yet.
5 NHTSA safety recalls for the 1996 Ford F-250. Check your VIN at NHTSA.gov
VEHICLE SPEED CONTROL
ON CERTAIN TRUCKS EQUIPPED WITH SPEED CONTROL, GASOLINE OR NATURAL GAS ENGINES, THE SPEED CONTROL DEACTIVATION SWITCH MAY OVERHEAT.
OVERHEATING COULD RESULT IN SMOKE OR BURN AND AN UNDERHOOD FIRE.
DEALERS WILL INSTALL A FUSED WIRING HARNESS INTO THE SPEED CONTROL SYSTEM FREE OF CHARGE. THE RECALL BEGAN ON AUGUST 7, 2006. OWNERS MAY CONTACT FORD AT 1-866-436-7332. (NOTE: ALSO SEE RECALLS 05V017 AND 05V388)
EXTERIOR LIGHTING
CERTAIN CK MOTORSPORTS COMBINATION HEADLIGHTS, CLEAR CORNER, BUMPER, AND SIDE MARKER LIGHTS SOLD AS REPLACEMENT LAMPS FOR USE ON THE PASSENGER VEHICLES LISTED ABOVE. SOME COMBINATION LAMPS THAT ARE NOT EQUIPPED WITH AMBER SIDE REFLECTORS FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.
WITHOUT THE AMBER REFLECTORS, THE VEHICLE WILL BE POORLY ILLUMINATED, POSSIBLY RESULTING IN A VEHICLE CRASH WITHOUT WARNING.
CK MOTORSPORT WILL NOTIFY OWNERS AND REPLACE THE NONCOMPLIANT LAMPS FREE OF CHARGE. THE RECALL BEGAN ON JULY 1, 2006. OWNERS MAY CONTACT CK MOTORSPORT AT 1-909-610-7211.
VEHICLE SPEED CONTROL
ON CERTAIN PICKUP TRUCKS AND SPORT UTILITY VEHICLES EQUIPPED WITH SPEED CONTROL, THE SPEED CONTROL DEACTIVATION SWITCH MAY OVERHEAT, SMOKE, OR BURN.
A FIRE AT THE SWITCH COULD OCCUR.
BY LETTER DATED SEPTEMBER 12, 2005, OWNERS WERE INSTRUCTED TO RETURN THEIR VEHICLES TO THEIR DEALERS TO HAVE THE SPEED CONTROL DEACTIVATION SWITCH DISCONNECTED. OWNERS WHO HAVE HAD THEIR SPEED CONTROL DEACTIVATED ARE BEING NOTIFIED THAT PARTS WILL BE AVAILABLE AND ADVISED TO MAKE AN APPOINTMENT TO RECONNECT THE SPEED CONTROL BEGINNING IN FEBRUARY 2006. OWNERS WHO DID NOT HAVE THEIR SPEED CONTROL DEACTIVATED ARE BEING NOTIFIED TO HAVE THEIR SYSTEM REMEDIED BEGINNING IN FEBRUARY 2006. OWNERS ARE URGED TO AVAIL THEMSELVES OF THE FREE DISCONNECT SERVICE AS SOON AS POSSIBLE BECAUSE OF THE SIGNIFICANT RISK OF FIRE. OWNERS MAY CONTACT FORD AT 1-800-392-3673. (NOTE: ALSO SEE RECALLS 05V017 AND 06V286)
EQUIPMENT:OTHER:LABELS
THE CERTIFICATION LABELS ON THE INVOLVED VEHICLES HAS INCORRECT REAR TIRE INFLATION PRESSURE DESIGNATIONS. THIS DOES NOT COMPLY WITH FMVSS NO. 120, "TIRE SELECTION AND RIMS FOR MOTOR VEHICLES OTHER THAN PASSENGER CARS."
INCORRECT INFLATION PRESSURES COULD CAUSE PREMATURE WEAR OF THE REAR TIRES. .
OWNERS WILL BE PROVIDED WITH CORRECT CERTIFICATION LABELS AND INSTRUCTIONS FOR INSTALLING THESE LABELS. DEALERS CAN INSTALL THIS LABEL IF THE OWNER SO DESIRES.
STRUCTURE:FRAME AND MEMBERS
THE CROSSMEMBER FRAME GUSSETS WERE INSTALLED WITH UNDERSIZED THREADED FASTENERS FOLLOWING A BREAKDOWN OF THE PRODUCTION RIVET GUN THAT IS GENERALLY USED. THIS GUSSET IS THE ATTACHMENT POINT FOR THE REAR STRAP OF THE MID-SHIP FUEL TANK.
THE SUBJECT FASTENERS CAN SEPARATE CAUSING IN THE REAR STRAP OF THE AFFECTED FUEL TANK TO BECOME DISCONNECTED. A LOOSE OR DISCONNECTED REAR STRAP ALLOWS THE FUEL TANK TO POSSIBLY CONTACT THE ROAD SURFACE INCREASING THE RISK OF A VEHICLE FIRE.
DEALERS WILL REPLACE THE CROSSMEMBER GUSSET FASTENERS WITH THE SPECIFIED ALTERNATIVE FASTENERS (BOLTS).