2000 Jaguar S-Type
Vehicle Specs & Maintenance Data
The 2000 Jaguar S-Type maintenance specs on this page cover the key fluids, torque values, and wear items you need for routine service. Use these numbers as a quick reference when performing oil changes, tire rotations, brake jobs, and other scheduled maintenance on your Jaguar S-Type.
For oil changes, the 2000 Jaguar S-Type takes 5W-20 Full Synthetic motor oil with a capacity of 6.9 quarts. Brake fluid type is DOT 4, the recommended coolant is OAT Coolant (Orange), and transmission fluid is ZF Lifeguard 8 (ATF). Always use the manufacturer-recommended fluids to maintain warranty coverage and engine longevity.
When mounting wheels on the Jaguar S-Type, torque the lug nuts to 92 ft-lbs using a calibrated torque wrench. Over- or under-torquing can lead to warped brake rotors or loose wheels. Re-torque after 50 to 100 miles on newly installed wheels.
There are 4 NHTSA safety recalls on file for the 2000 Jaguar S-Type. Check the Recalls tab below for full details.
Specifications on this page are compiled from multiple publicly available sources including manufacturer documentation, NHTSA data, and automotive databases. Always cross-reference with your owner's manual or official factory documentation before purchasing parts or performing any service.
The 2000 Jaguar S-Type uses 5W-20 Full Synthetic motor oil (6.9 qt capacity), requires lug nuts torqued to 92 ft-lbs, takes DOT 4 brake fluid.
Enter a diagnostic trouble code to see causes, symptoms, and fixes for the 2000 Jaguar S-Type.
No known problems reported for this vehicle yet.
4 NHTSA safety recalls for the 2000 Jaguar S-Type. Check your VIN at NHTSA.gov
FUEL SYSTEM, GASOLINE
CERTAIN AFTERMARKET FUEL FILTERS SOLD UNDER THE PUROLATOR BRAND NAME, P/N F65277, SHIPPED FROM JANUARY 16 THROUGH JUNE 2, 2006, FOR USE ON THE ABOVE LISTED PASSENGER VEHICLES. DUE TO INCORRECT DESIGN, THE QUICK CONNECTORS MAY NOT FULLY SEAT WITH THE TUBE INTERFACE, EVEN THOUGH THE PERSON MAKING THE CONNECTION MAY BELIEVE THAT THE QUICK CONNECTOR IS FULLY ATTACHED.
FAILURE OF THIS CONNECTION COULD LEAD TO FUEL SPILLAGE AND, IN THE PRESENCE OF AN IGNITION SOURCE, A FIRE COULD OCCUR.
UFI WILL NOTIFY OWNERS AND REPLACE THE FILTERS FREE OF CHARGE. THE RECALL BEGAN ON AUGUST 4, 2006. OWNERS MAY CONTACT UFI FILTERS USA AT 800-230-5876.
FUEL SYSTEM, GASOLINE
CERTAIN REPLACEMENT FUEL FILTERS, FRAM BRAND NAME P/N G3727, WITH DATE CODES X52911 THROUGH X60801 SEQUENTIALLY OR X600141 AND A MEXICO COUNTRY OR ORIGIN MARKING ON THE FUEL FILTER HOUSING MANUFACTURED FROM OCTOBER 18, 2005, THROUGH MARCH 21, 2006, SOLD FOR USE ON THE VEHICLES LISTED ABOVE AND ON CERTAIN SCHOOL BUSES. (TO SEE THE SCHOOL BUS ENGINE SIZES, CLICK ON "DOCUMENT SEARCH" AND THEN "BUS APPLICATIONS"). THE CONNECTOR ON THE FUEL FILTER WAS NOT MANUFACTURED TO HONEYWELL'S SPECIFICATION. AS A RESULT, THE O-RING MAY NOT SEAT CORRECTLY ON THE FUEL LINE.
THIS CONDITION MAY CAUSE AN INADEQUATE SEAL AT THE CONNECTION, POTENTIALLY LEADING TO A FUEL LEAK. IN THE PRESENCE OF AN IGNITION SOURCE, A FIRE COULD OCCUR.
HONEYWELL WILL NOTIFY OWNERS AND REPLACE THE FUEL FILTERS FREE OF CHARGE. THE RECALL BEGAN ON OCTOBER 18, 2006. OWNERS MAY CONTACT FRAM CUSTOMER SERVICE AT 1-800-890-2075 (OPTION 1).
SUSPENSION:FRONT:CONTROL ARM:LOWER BALL JOINT
VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE FRONT SUSPENSION LOWER BALL JOINTS WERE NOT TIGHTENED TO SPECIFICATIONS WHEN THEY WERE ATTACHED TO THE LOWER CONTROL ARMS.
IF THE BALL JOINT ATTACHING NUTS ARE NOT ADEQUATELY TIGHTENED, THEY CAN LOOSEN AND ULTIMATELY, RESULT IN FRACTURE OF THE BALL JOINT STUD. IF THE BALL JOINT FRACTURES, CONTROL OF THE VEHICLE COULD BE AFFECTED, INCREASING THE RISK OF A CRASH.
DEALERS WILL INSPECT THE TORQUE ON THE TWO BALL JOINT ATTACHING NUTS. VEHICLES WITH LOOSE BALL JOINT ATTACHING NUTS WILL EITHER HAVE THE FASTENERS TIGHTENED TO SPECIFICATION, OR IF NECESSARY, THE BALL JOINTS WILL BE REPLACED.
SEAT BELTS
VEHICLE DESCRIPTION: PASSENGER VEHICLES EQUIPPED WITH TRW SEAT BELT BUCKLE ASSEMBLIES. THE BUCKLE BASE OF THESE SEAT BELT ASSEMBLIES WERE NOT PROPERLY HEAT TREATED AND THEREFORE DO NOT PASS THE LOAD BEARING REQUIREMENT OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 209, "SEAT BELT ASSEMBLIES."
IN THE EVENT OF A VEHICLE CRASH, THE OCCUPANT MAY NOT BE PROPERLY RESTRAINED.
DEALERS WILL INSPECT AND CHANGE, IF NECESSARY, THE SEAT BELT BUCKLES.