1995 Ford F-250
Vehicle Specs & Maintenance Data
The 1995 Ford F-250 maintenance specs on this page cover the key fluids, torque values, and wear items you need for routine service. Use these numbers as a quick reference when performing oil changes, tire rotations, brake jobs, and other scheduled maintenance on your Ford F-250.
For oil changes, the 1995 Ford F-250 takes 5W-20 Full Synthetic motor oil with a capacity of 8 quarts. Brake fluid type is DOT 3, the recommended coolant is Motorcraft Gold (OAT), and transmission fluid is Mercon LV. Always use the manufacturer-recommended fluids to maintain warranty coverage and engine longevity.
When mounting wheels on the Ford F-250, torque the lug nuts to 140 ft-lbs using a calibrated torque wrench. Over- or under-torquing can lead to warped brake rotors or loose wheels. Re-torque after 50 to 100 miles on newly installed wheels.
There are 4 NHTSA safety recalls on file for the 1995 Ford F-250. Check the Recalls tab below for full details.
Specifications on this page are compiled from multiple publicly available sources including manufacturer documentation, NHTSA data, and automotive databases. Always cross-reference with your owner's manual or official factory documentation before purchasing parts or performing any service.
The 1995 Ford F-250 uses 5W-20 Full Synthetic motor oil (8 qt capacity), requires lug nuts torqued to 140 ft-lbs, takes DOT 3 brake fluid.
Enter a diagnostic trouble code to see causes, symptoms, and fixes for the 1995 Ford F-250.
No known problems reported for this vehicle yet.
4 NHTSA safety recalls for the 1995 Ford F-250. Check your VIN at NHTSA.gov
VEHICLE SPEED CONTROL
ON CERTAIN TRUCKS EQUIPPED WITH SPEED CONTROL, GASOLINE OR NATURAL GAS ENGINES, THE SPEED CONTROL DEACTIVATION SWITCH MAY OVERHEAT.
OVERHEATING COULD RESULT IN SMOKE OR BURN AND AN UNDERHOOD FIRE.
DEALERS WILL INSTALL A FUSED WIRING HARNESS INTO THE SPEED CONTROL SYSTEM FREE OF CHARGE. THE RECALL BEGAN ON AUGUST 7, 2006. OWNERS MAY CONTACT FORD AT 1-866-436-7332. (NOTE: ALSO SEE RECALLS 05V017 AND 05V388)
EXTERIOR LIGHTING
CERTAIN CK MOTORSPORTS COMBINATION HEADLIGHTS, CLEAR CORNER, BUMPER, AND SIDE MARKER LIGHTS SOLD AS REPLACEMENT LAMPS FOR USE ON THE PASSENGER VEHICLES LISTED ABOVE. SOME COMBINATION LAMPS THAT ARE NOT EQUIPPED WITH AMBER SIDE REFLECTORS FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.
WITHOUT THE AMBER REFLECTORS, THE VEHICLE WILL BE POORLY ILLUMINATED, POSSIBLY RESULTING IN A VEHICLE CRASH WITHOUT WARNING.
CK MOTORSPORT WILL NOTIFY OWNERS AND REPLACE THE NONCOMPLIANT LAMPS FREE OF CHARGE. THE RECALL BEGAN ON JULY 1, 2006. OWNERS MAY CONTACT CK MOTORSPORT AT 1-909-610-7211.
VEHICLE SPEED CONTROL
ON CERTAIN PICKUP TRUCKS AND SPORT UTILITY VEHICLES EQUIPPED WITH SPEED CONTROL, THE SPEED CONTROL DEACTIVATION SWITCH MAY OVERHEAT, SMOKE, OR BURN.
A FIRE AT THE SWITCH COULD OCCUR.
BY LETTER DATED SEPTEMBER 12, 2005, OWNERS WERE INSTRUCTED TO RETURN THEIR VEHICLES TO THEIR DEALERS TO HAVE THE SPEED CONTROL DEACTIVATION SWITCH DISCONNECTED. OWNERS WHO HAVE HAD THEIR SPEED CONTROL DEACTIVATED ARE BEING NOTIFIED THAT PARTS WILL BE AVAILABLE AND ADVISED TO MAKE AN APPOINTMENT TO RECONNECT THE SPEED CONTROL BEGINNING IN FEBRUARY 2006. OWNERS WHO DID NOT HAVE THEIR SPEED CONTROL DEACTIVATED ARE BEING NOTIFIED TO HAVE THEIR SYSTEM REMEDIED BEGINNING IN FEBRUARY 2006. OWNERS ARE URGED TO AVAIL THEMSELVES OF THE FREE DISCONNECT SERVICE AS SOON AS POSSIBLE BECAUSE OF THE SIGNIFICANT RISK OF FIRE. OWNERS MAY CONTACT FORD AT 1-800-392-3673. (NOTE: ALSO SEE RECALLS 05V017 AND 06V286)
SEATS
THE WIRE HARNESS FOR THE POWER LUMBAR FEATURE ON THE SEAT IS UNDERNEATH THE FRONT SEAT CUSHION SUPPORT WIRES. THE SUPPORT WIRES ON THE DRIVER SEAT CAN CONTACT AND DAMAGE THE INSULATION HARNESS RESULTING IN A HIGH RESISTANCE ELECTRICAL SHORT THROUGH THE SUPPORT WIRES.
CONSEQUENCE OF DEFECT: OVER HEATING OF THE SUPPORT WIRES COULD RESULT, AND MELTING, SMOKE, OR POSSIBLE IGNTION OF THE SURROUNDING MATERIALS COULD OCCUR.
DEALERS WILL INSPECT THE SEATS ON THE AFFECTED VEHICLES. IF NO DAMAGE IS FOUND, THE DRIVER SEAT WIRE HARNESS WILL BE COVERED WITH A PROTECTIVE CONVOLUTE TUBING, WRAPPED WITH ELECTRICAL TAPE AND THE HARNESS WILL BE REROUTED. IF DAMAGE IS FOUND, THE WIRE HARNESS WILL BE REPLACED.