2006 Mazda Tribute
Vehicle Specs & Maintenance Data
The 2006 Mazda Tribute maintenance specs on this page cover the key fluids, torque values, and wear items you need for routine service. Use these numbers as a quick reference when performing oil changes, tire rotations, brake jobs, and other scheduled maintenance on your Mazda Tribute.
For oil changes, the 2006 Mazda Tribute takes 5W-20 Full Synthetic motor oil with a capacity of 5.5 quarts. Brake fluid type is DOT 3, the recommended coolant is FL22 Long Life Coolant (Green), and transmission fluid is Mazda ATF FZ. Always use the manufacturer-recommended fluids to maintain warranty coverage and engine longevity.
When mounting wheels on the Mazda Tribute, torque the lug nuts to 100 ft-lbs using a calibrated torque wrench. Over- or under-torquing can lead to warped brake rotors or loose wheels. Re-torque after 50 to 100 miles on newly installed wheels.
There are 3 NHTSA safety recalls on file for the 2006 Mazda Tribute. Check the Recalls tab below for full details.
Specifications on this page are compiled from multiple publicly available sources including manufacturer documentation, NHTSA data, and automotive databases. Always cross-reference with your owner's manual or official factory documentation before purchasing parts or performing any service.
The 2006 Mazda Tribute uses 5W-20 Full Synthetic motor oil (5.5 qt capacity), requires lug nuts torqued to 100 ft-lbs, takes DOT 3 brake fluid.
Enter a diagnostic trouble code to see causes, symptoms, and fixes for the 2006 Mazda Tribute.
No known problems reported for this vehicle yet.
3 NHTSA safety recalls for the 2006 Mazda Tribute. Check your VIN at NHTSA.gov
SUSPENSION:FRONT:WHEEL BEARING
The Timken Company (Timken) is recalling certain aftermarket front wheel bearings, part number 510072, sold from January 22, 2015, to May 21, 2015, to be used as service parts on 2001-2012 Ford Escape, 2001-2011 Mazda Tribute, and 2005-2011 Mercury Mariner vehicles. The affected wheel bearings have incorrect dimensions of a 42mm bore, 76mm outer dimension, and 39mm width, instead of a 42mm bore, 78mm outer dimension and a 45mm width.
Use of an incorrectly sized wheel bearing can adversely affect the braking and steering of the vehicle, increasing the risk of a crash.
Timken has begun notifying distributors who will offer purchasers replacement wheel bearings, free of charge. The recall began on May 21, 2015. Owners may contact Timken customer service at 1-866-984-6536.
ENGINE AND ENGINE COOLING
Mazda is recalling certain model year 2001 through 2006, and 2008, Tribute vehicles equipped with 3.0L V6 engines and speed control. Inadequate clearance between the engine cover and the speed control cable connector could result in a stuck throttle when the accelerator pedal is fully or almost-fully depressed. This risk exists regardless of whether or not speed control (cruise control) is used.
A stuck throttle may result in very high vehicle speeds and make it difficult to stop or slow the vehicle, which could cause a crash, serious injury or death.
Mazda will notify owners, and dealers will repair the vehicles by increasing the engine cover clearance, free of charge. Remedy parts are now available. The safety recall began on September 13, 2012. Owners may contact Mazda Customer Assistance Center at 1-800-222-5500, option #6.
VISIBILITY:WINDSHIELD WIPER/WASHER:MOTOR
ON CERTAIN TRUCKS AND SPORT UTILITY VEHICLES, THE WINDSHIELD WIPER MOTOR MAY HAVE BEEN PRODUCED WITHOUT GREASE APPLIED TO THE OUTPUT SHAFT GEAR.
AFTER A PERIOD OF CONTINUOUS USE ON THE HIGH SPEED SETTING, LACK OF GREASE ON THE OUTPUT SHAFT GEAR MAY CAUSE THE GEAR TEETH TO DISTORT OR FRACTURE DURING OPERATION RESULTING IN THE LOSS OF WIPER FUNCTION. INOPERATIVE WIPERS UNDER INCLEMENT WEATHER CONDITIONS COULD CAUSE A CRASH DUE TO IMPAIRED VISIBILITY.
DEALERS WILL INSPECT THE WIPER MOTOR FOR THE PRESENCE OF GREASE AND GREASE THE WIPER MOTOR GEARS IF NECESSARY. THE RECALL BEGAN ON NOVEMBER 28, 2005. OWNERS MAY CONTACT MAZDA AT 1-800-222-5500.